Cables & Adapters

PCAN Cables 1 & 2 – 2m CAN cables with DB9/F Connectors
PCAN-Kabel_02

  • 9-pin D-Sub sockets (in accordance with CiA® 102) at both ends
  • Length 2.0 m
  • Shield connected to GND
  • PCAN-Cable 1 without termination resistors
  • PCAN-Cable 2 with 120 Ohm termination resistors
  • Suitable for the use in CAN FD busses
  • NOTE: Custom length cables are available upon request
Go to top
PCAN Cable 3 – 2m CAN Cable for Test and Measurement Setups
PCAN-Kabel3

  • 9-pin D-Sub socket (in accordance with CiA® 102) to banana plugs 4 mm for picking up the signals CAN-High and CAN-Low
  • Without termination resistors
  • Length 2.0 m
  • Suitable for the use in CAN FD busses
  • NOTE: Custom length cable is available upon request
Go to top
PCAN-LIN Connection Cable – Pre-configured Cable Set for the PCAN-LIN Module
PCAN-LIN-Connection-Cable

  • Pre-configured cable set for PCAN-LIN
  • Split-up of the lines from the CAN/LIN connector to:
    • CAN (D-Sub plug, 9-pin)
    • LIN (banana plug, 4 mm)
    • Power supply (banana plugs, 4 mm)
  • Without terminating resistor
  • Length about 0.75 m
  • Suitable for the use in CAN FD busses
  • Please note: The PCAN-LIN Connection cable is not suitable for use with the PCAN-USB Pro FD.
Go to top
PCAN-Cable OBD-2 – CAN-OBD-2 Diagnostics Cable
PCAN-Kabel-OBD-2_2012

  • 9-pin D-Sub socket (in accordance with CiA® 102)
  • OBD-2 connector – assigned for CAN only on:
    • Pin 6: CAN High (J-2284)
    • Pin 14: CAN Low (J-2284)
  • Length 1.0 m
  • Without termination resistors
  • All ODB-2 pins are mounted in the plug and can be assigned as desired
Go to top
PCAN-Cable OBD-2 – CAN-OBD-2 Diagnostics Cable
PCAN-Kabel_J1939

  • 9-pin D-Sub socket (in accordance with CiA® 102) to 9-pole DEUTSCH connector of the HD series
  • DEUTSCH connector assignment
    • C: CAN-High
    • D: CAN-Low
    • E: CAN-Shield
  • Length 1 m
  • Without termination resistor
Go to top
PCAN-Term – 120 Ohm CAN Termination Adapter
PCAN-Term_2012Wiring_Term

  • CAN termination adapter in plastic casing
  • 9-pin D-Sub socket to 9-pin D-Sub connector
    (in accordance with CiA® 102)
  • With 120 Ohm termination resistor between
    CAN_L and CAN_H
  • Suitable for the use in CAN FD busses
Go to top
PCAN-MiniTerm – mini 120 Ohm CAN Termination Adapter
PCAN-MiniTerm_WideWiring_Term-1

  • CAN termination adapter in molded body
  • 9-pin D-Sub socket to 9-pin D-Sub connector (in accordance with CiA® 102)
  • All connector pins are connected 1 to 1
  • With 120 Ohm termination resistor between CAN_L and CAN_H
  • Suitable for the use in CAN FD busses
Go to top
PCAN-T-Adapter – T-Adapter for CAN Tapping
PCAN-T-Adapter_2012Wiring_T-Adapter
The PCAN-T-Adapter creates a tap connection to the data cables and the ground within a CAN bus in order to be able to connect a CAN node. In this case, the CAN node is not terminated.

  • 9-pin D-Sub socket to 9-pin D-Sub connector and D-Sub socket (in accordance with CiA® 102)
  • CAN tap length about 20 cm
  • Unterminated
Go to top
PCAN-D-Sub Connection Adapter – D-Sub Connection Adapter for Screw Terminal Blocks
PCAN-D-Sub-Adapter_01Wiring_D-Sub-Adapter

  • 4-pin screw terminal block (Phoenix) to 9-pin D-Sub socket (according to CiA® 102)
  • Suitable for CAN connection adaptation of the products:
    • PCAN-Repeater DR
    • PCAN-Router DR
    • PCAN-Ethernet Gateway DR
    • PCAN-Wireless Gateway DR
  • No termination
  • Suitable for the use in CAN FD busses